翻訳と辞書
Words near each other
・ "O" Is for Outlaw
・ "O"-Jung.Ban.Hap.
・ "Ode-to-Napoleon" hexachord
・ "Oh Yeah!" Live
・ "Our Contemporary" regional art exhibition (Leningrad, 1975)
・ "P" Is for Peril
・ "Pimpernel" Smith
・ "Polish death camp" controversy
・ "Pro knigi" ("About books")
・ "Prosopa" Greek Television Awards
・ "Pussy Cats" Starring the Walkmen
・ "Q" Is for Quarry
・ "R" Is for Ricochet
・ "R" The King (2016 film)
・ "Rags" Ragland
・ ! (album)
・ ! (disambiguation)
・ !!
・ !!!
・ !!! (album)
・ !!Destroy-Oh-Boy!!
・ !Action Pact!
・ !Arriba! La Pachanga
・ !Hero
・ !Hero (album)
・ !Kung language
・ !Oka Tokat
・ !PAUS3
・ !T.O.O.H.!
・ !Women Art Revolution


Dictionary Lists
翻訳と辞書 辞書検索 [ 開発暫定版 ]
スポンサード リンク

Dolby noise reduction : ウィキペディア英語版
Dolby noise-reduction system

A Dolby noise-reduction system, or Dolby NR, is one of a series of noise reduction systems developed by Dolby Laboratories for use in analog magnetic tape recording. The first was ''Dolby A'', a professional broadband noise reduction for recording studios in 1965, but the best-known is ''Dolby B'' (introduced 1968), a sliding band system for the consumer market, which helped make high fidelity practical on cassette tapes, and is common on stereo tape players and recorders to the present day. Of the noise reduction systems, ''Dolby A'' and ''Dolby SR'' were developed for professional use. ''Dolby B'', ''C'', and, ''S'' were designed for the consumer market. Aside from Dolby HX, all the Dolby variants work by companding, or ''comp''ressing the dynamic range of the sound during recording and ex''panding'' it during playback.
== How Dolby noise reduction works ==
Dolby noise reduction is a form of dynamic preemphasis employed during recording, plus a form of dynamic deemphasis used during playback, that work in tandem to improve the signal-to-noise ratio. While Dolby A operates across the whole spectrum, the other systems specifically emphasize the audible frequency range where background tape hiss, an artifact of the recording process that is similar to white noise, is most noticeable (usually above 1 kHz, or two octaves above Middle C).
The Dolby preemphasis boosts the recorded level of the quieter audio signal at these higher frequencies during recording, effectively compressing the dynamic range of that portion of the signal, so that quieter sounds above 1 kHz receive a proportionally greater boost. As the tape is recorded, the relative amplitude of the signal above 1 kHz is used to determine how much pre-emphasis to apply - a low-level signal is boosted by 10 dB (Dolby B) or 20 dB (Dolby C). As the signal rises in amplitude, less and less pre-emphasis is applied until at the "Dolby level" (0 VU), no signal modification is performed.
The sound is thus recorded at a higher overall level on the tape relative to the tape's overall noise level, requiring the tape formulation to preserve this specially recorded signal without distortion. On playback, the opposite process is applied (deemphasis), based on the relative signal component above 1 kHz. Thus as this portion of the signal decreases in amplitude, the higher frequencies are progressively more sharply attenuated, which also filters out the constant background noise on the tape when and where it would be most noticeable.
The two (pre and de-emphasis) processes are intended to cancel each other out as far as the actual recorded program is concerned. Only de-emphasis is applied to the incoming signal and noise during playback. After playback de-emphasis is complete, apparent noise in the output signal is reduced, and this process should not produce any effect noticeable to the listener (other than reduced noise of course). Playback without noise reduction produces a noticeably brighter sound, however.
The calibration of the recording and playback circuitry is therefore critical for faithful reproduction of the original program content, and this is easily offset by poor quality tape, dirty recording/playback heads, or using inappropriate bias levels/frequency for the tape formulation, as well as tape speed, when recording or duplicating. This can manifest itself as muffled-sounding playback, or "breathing" of the noise level as the signal varies.
On some high end consumer equipment, Dolby calibration control is included: for recording, a reference tone at Dolby level may be recorded for accurate playback level calibration on another transport; at playback, the same recorded tone should produce the identical output, as indicated by a Dolby logo marking at 0 VU on the VU meter(s). (In consumer equipment Dolby Level is defined as 200 nWb/m; calibration tapes were available to assist correct level setting.) For accurate off-the-tape monitoring during recording on 3-head decks, both processes must be employed at once, and circuitry provided to accomplish this is marketed under the rubric "Double Dolby".

抄文引用元・出典: フリー百科事典『 ウィキペディア(Wikipedia)
ウィキペディアで「Dolby noise-reduction system」の詳細全文を読む



スポンサード リンク
翻訳と辞書 : 翻訳のためのインターネットリソース

Copyright(C) kotoba.ne.jp 1997-2016. All Rights Reserved.